Poles	2~20P
Current rating	3A AC,DC
Voltage raing	250V AC,DC
Temperature range	-25℃～+85℃
Contact resistance	≤10mΩ
Insulation resistance	≥1000MΩ
Withstand voltage	1000VAC/minute
Applicable wire	AWG #30 to #22

Performance test:

	Item	Test condition	Requirements
1	Appearance	Visual by eye Light: >1.0 Lamp: 200~300Lx Space: 0.3~0.5m	1. Plastic part:smooth and flat surface without discolor,broken,crack distortion defects is acceptable. 2.Metal part:btight and even surface without rust,oxide,fog and obvious physical damage defects is acceptable. 3.Wire:clearing surface without discolor,broken defects,indistinct words and mark is acceptable.
2	Contact resistance	Mate connectors,measure by dry circuit.	10mΩ MAX
3	InsuIation Resistance	Apply 500V DC between adjacent terminal or ground.	1000MΩ MIN
4	Dielectric Strength	Mate connectors,apply 500V AC for 1 minute between adjacent terminal or ground.	No Breakdown
5	Crimping Pull Out Force	Fix the crimped terminal,apply axial pull out force on the wire at the speed rate of not more 25mm/min.	AWG.22# 30N MIN AWG.24# 20N MIN AWG.26# 15N MIN AWG.28# 10N MIN AWG.30# 8N MIN
6	Terminal/Housing Retention Force	Apply axial pull out force at the speed rate of not more 25mm/min on the pin assembled in the housing.	15N MIN
7	Pin Retention Force	Apply axial push out force at the speed rate of not more 25mm/minute on the terminal assembled in the base.	10N MIN
8	Solderability	Soldering time: 2±0.5 second Solder Temperature:240℃±5℃	90% of immersed area must show no voids,pin holes
9	Resistance to Soldering Heat	Soldering time: 2±0.5 second Solder Temperature:260℃	Appearance	No Damage
10	Heat Resistance	Mated connectors are exposed to a temperature of 85℃±2℃ for 96 hours.	Appearance LLCR	No Damage 20mΩ Max
11	Clod Resistance	Mated connectors are exposed to a temperature of -25℃±2℃ for 96 hours.	Appearance LLCR	No Damage 20mΩ Max
12	Temperature Rise	Carring rated current load.	Temperature Rise	30℃ MAX
13	Humidity	Temperature:40±2℃ Relative Humidity:90%~95% Duration:96 hours	Appearance	No damage
			Dielectric strength	1000VAC/minute
			Insulation Resistance LLCR	1000MΩ MIN
			Insulation Resistance LLCR	20mΩ MAX
14	Temperature cycle	Mated connectors are exposed to 5 cycles of: a)-25°C±2°C 0.5hour b)+85°C±2°C 0.5hour	Appearance	No damage
			Dielectric strength	1000VAC/minute
			Insulation Resistance LLCR	1000MΩ MIN
			Insulation Resistance LLCR	20mΩ MAX
15	Vibration	Frequency:10~55Hz Amplitude:±1.5mm Frequency:>55~500Hz Acceleration:50m/s2 Duration:2 hours in each X,Y,Z axes	Appearance	No damage
			Contact resistance	20mΩ MAX
			Intermittence	1μsec MAX
16	Repeated insertion/ withdrawal	When mated up to 50 cycles repeatedly by the rate of 10 cycles per minute.	Appearance	No damage
			Dielectric strength	1000VAC/minute
			Insulation	1000MΩ MIN
			Contact resistance	20mΩ MAX
17	Salt spray	16 hour exposure to a saltspray from the 5%±1 solution.	Appearance:No Damage(No erosion with material exposed.And with plating material,slight erosion on the cutting surface acceptable)
18	Insertion and Withdrawal Force	Insertion and withdraw contact at the speed rate of 1mm/s~5mm/s.	Insertion(Max)	Withdrawal(Min)
18	Insertion and Withdrawal Force		10N	2.0N

Dimension: (mm)

Product Tags:

wire to board connector

wiring bnc connector

board to wire connector

Inquiry Cart 0